RLPRO Panel — Digital Manual
RLPRO 200 MAX & 300 MAX
Your digital manual.
Everything in one place.
Set up, first session, controls and troubleshooting, all here.
Downloads
Save your manuals
Download the PDFs to keep on your device. No internet needed.
Unboxing
What's in your box
Missing something? Email hello@lum8wellness.com within 7 days with your order number and a photo of the packaging.
Installation
Setting up your panel
Attach the hanging hardware. Lay the panel face down on a soft surface. Screw the two threaded posts into the top, then screw the braided cables onto the posts.
Choose your mount. Wall mount, hardware included. Door hook, no drilling. Pulley system to raise and lower the panel. Panel stand, sold separately (complete sets). Always support the panel while raising or lowering it.
Connect power. Plug the cable into the back of the panel first, then into an earthed wall outlet. Switch the red power switch on and the touchscreen will light up.
Day One
Your first session
Put on your eyewear. Always. Near infrared light is invisible but still working. Eyewear protects your eyes in every mode.
Tap Scene. Choose a preset and the panel sets itself up. Try Universal for your first session. You can still adjust the settings afterwards.
Sit or stand 25 to 30cm away and tap Run. Start with 5 to 10 minutes. A gentle warmth is normal. Build up gradually over two weeks.
Scene presets on your panel
UniversalSkinSleepMuscleJoint PainFat LossPetThe Sleep preset uses red light. If it feels bright, tap Brightness after choosing it and lower it to suit.
How often?
Three to five sessions a week suits most people, and daily use is fine too. Consistency over weeks matters more than the length of any one session. The manufacturer recommends waiting 6 hours between 30 minute sessions. In the evening, use Red at a lower brightness.
The light
Your 8 wavelengths
Three modes: Red (630 to 670nm) · NIR (810 to 1060nm) · Red and NIR (all 8). In NIR mode the panel looks off because the light is invisible. It is still working.
Controls
Touchscreen quick guide
Remote control uses a CR2032 battery (not included).
Technical data
Specifications
| 200 MAX | 300 MAX | |
|---|---|---|
| LEDs | 144 | 288 |
| Rated power | 240W | 480W |
| Wavelengths | 630, 650, 660, 670, 810, 830, 850, 1060nm | |
| Irradiance | 160 mW/cm² typical at 15cm (6 inches), red and NIR combined. 140 mW/cm² guaranteed minimum | |
| Lens angle | 30° | |
| Size | 480 × 300 × 65mm | 920 × 300 × 65mm |
| Weight | 8.5kg | 13.5kg |
| Input | 220 to 240V AC, 50 to 60Hz | |
| EMF | 0.0 µT at 4 inches | |
| Surface temperature | 40°C or less | |
| Operating temperature | 5 to 50°C | |
| Certification | RCM, certificate GMA-525932-EA | |
| Warranty | 3 years | |
Help
Troubleshooting
Panel won't turn on
Check the cable at both ends and that the outlet is on. Switch on the red power switch on the back.
Panel stopped during a session
The timer finished. If no time was set, the panel stops after 5 minutes. Set a longer time under Timer.
LEDs look off
NIR light is invisible, so the panel is working normally. Switch to Red, or Red and NIR, to see the light. Keep your eyewear on.
Pulse isn't working
Open Pulse and set a frequency.
Remote not working
Fit a new CR2032 battery and point the remote at the panel.
Touchscreen not responding
Switch off at the rear switch, wait 30 seconds, then switch on again. If it continues, go to Other Setting, then Factory Reset.
Very hot, unusual smell or noise
Stop, unplug and email hello@lum8wellness.com before using it again.
Safety
Before you start
Never look directly into the LEDs. Use indoors only, away from water and heat, and unplug when not in use. Keep cables away from children. Talk to your doctor first if you are pregnant or breastfeeding, photosensitive, taking photosensitising medication, or have a light triggered condition. Stop if anything feels uncomfortable.
LUM8 RLPRO panels are wellness devices, not medical devices. They are not intended to diagnose, treat, cure or prevent any condition. Full safety information is in the product manual.
Warranty
3 year warranty
Your panel has a 3 year LUM8 warranty against defects, from the date of purchase. To make a claim, email hello@lum8wellness.com with your order number.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
Community
Join us on Instagram
Routines, research and product updates at @lum8wellness
Follow @lum8wellnessWe're here if you need us.
We will respond within one to two business days.
hello@lum8wellness.com lum8wellness.com© 2026 Tory Giles Health Pty Ltd · Noosa QLD Australia